Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Mesquite Homeowners
When a driveway gate stops opening, the whole routine of the house stops with it. You are stuck parking in the street, hauling groceries through a side door, or leaving the gate propped with a brick so the car can get out. Ironworks Gate Co. repairs driveway and estate gates across Mesquite, from electric and automatic systems to hinges, welds, locks, and alignment. Our technicians have up to 13 years of experience on gate hardware and automation, and we handle the brands you are most likely to own, including LiftMaster and DoorKing. We answer the phone 24 hours a day, so a gate that quits on a Saturday night is not a wait-until-Monday problem. Call (844) 797-2573 and we will get a repair scheduled. Every job is backed in writing by our 90-Day Done Right Promise.

What Our Gate Repair Service Includes
Gate repair covers a lot of ground. A gate can fail because the motor is tired, because a hinge bolt has worked loose in the desert soil, because the frame has sagged out of square, or because rust has eaten a weld joint from the inside out. Here is how we handle each of the common repairs.
Electric Gate Repair
Electric gate repair covers the power side of the system: the transformer, the wiring run, the control board, and the low-voltage accessories that tell the gate what to do. You need it when the gate is dead in place with no motor sound at all, when a breaker trips every time the gate tries to move, or when a keypad or safety edge has quit. We trace the fault with a meter rather than guessing at parts, so the repair addresses the actual cause instead of the symptom. In Mesquite’s dry summer heat, we regularly find control-box wiring that has baked brittle and needs replacing before it fails outright.
Automatic Gate Repair
Automatic gate repair covers the operator itself: the motor, the gearbox, the limit switches, and the safety sensors that stop the gate from closing on a car or a person. You need it when the gate opens partway and reverses, moves in jerks, or stops responding to the remote. We service operators from LiftMaster, DoorKing, Elite, and Mighty Mule, and we test the safety reversing system on every call because a gate that closes on a vehicle is a real hazard. If the operator is beyond saving, we will tell you plainly and quote a replacement rather than sell you a repair that won’t hold.
Hinge & Post Repair
Hinge and post repair addresses the pivot points that carry the whole weight of the gate. You need it when the gate drags at the bottom, when a hinge pin has wallowed out its hole, or when the post has begun to lean. We reset hinge plates, replace worn pins and bearings, and re-set posts in proper concrete where the original footing has given way. In the older neighborhoods around Mesquite, we often find gate posts set shallow in caliche and cracked loose after years of heat cycling, and we reset them deep enough to stay put.
Gate Realignment
Gate realignment brings a sagged or racked gate back to square so it swings or slides freely and latches cleanly. You need it when the gate scrapes the ground, binds against the latch, or hangs visibly crooked at the free end. We measure the frame, check the diagonals, and adjust the hinges and stops so the gate travels the way it was built to. A gate that is out of alignment will wear out its motor early, so fixing the geometry often saves the operator as well.
Lock Repair
Lock repair covers the mechanical and electronic hardware that keeps the gate secured: latches, deadbolts, magnetic locks, and the keypads and receivers that release them. You need it when a key won’t turn, when the latch no longer catches, or when the keypad has stopped accepting a code. We repair or replace the lock hardware and re-test the release so the gate both secures and opens on command. A gate that won’t lock is a security gap, and we treat it as one.
Weld & Rust Repair
Weld and rust repair addresses the steel itself: cracked welds at the frame joints, rust-through at the bottom rail, and failed hinge mounts. You need it when you see rust bleeding through paint, a hairline crack near a joint, or a hinge that has torn loose from the frame. We cut out the corroded section and weld in new steel, then grind and finish the repair so it blends with the original work. Mesquite’s iron gates take a beating from sun and blowing dust, and we build repairs to last another twenty years.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Repair
We are trained and equipped on the gate-automation brands that show up most often on Mesquite driveways. LiftMaster operators are common on residential swing and slide gates, and we know their control boards and safety-sensor behavior well enough to diagnose a fault quickly. DoorKing systems turn up on heavier estate gates and gated entries, and we understand their loop and access-control logic. Elite and Mighty Mule operators round out the residential side, and we have repaired enough of both to know which parts tend to fail first.
Whatever make is on your driveway, the repair starts the same way: we identify the actual failure before touching a bolt. If your gate runs a brand not listed here, call and describe it. We will tell you straight whether we can help, and we are certified on nine leading gate-automation brands, from FAAC and BFT to Linear, Viking, and Ghost Controls. Whether you have a LiftMaster that won’t reverse or a DoorKing that has lost its codes, we can help.
Signs You Need Gate Repair Right Now
- The gate opens but won’t close, or reverses on its own. This usually points to a misaligned safety sensor or a failing limit switch, and it can leave the gate open all night. We test the reversing system and reset the limits so it closes reliably.
- The motor strains, hums, or clicks without moving the gate. A straining operator often means a binding hinge or a worn gearbox, and running it this way will burn out the motor. Better to catch it now than replace the whole operator later.
- The gate drags on the ground or scrapes the latch. That is a sign of sagging hinges or a post that has shifted, and it wears the gate and the motor every time it moves. Realignment takes the load off both.
- Rust, cracks, or a loose hinge on the frame. A cracked weld near a hinge can tear the mount completely free, and a gate that drops off its hinges is a genuine hazard. We weld and reinforce before it fails.
- The keypad, remote, or lock has stopped working. When the gate won’t release or won’t latch, you are either locked out or left unsecured. We repair the lock and access hardware and test the release on the spot.
Our Gate Repair Process – Step by Step
- 1
We take your call and ask the right questions. A live person answers 24 hours a day and asks what the gate is doing, what brand the operator is, and whether it swings or slides. Those answers help us arrive with the right tools and likely parts. No voicemail tree, no waiting until Monday.
- 2
We diagnose on site before quoting. We test the operator with a meter, check the power run, and measure the gate frame for alignment. On a binding gate we check the diagonals and hinge play; on an electrical fault we trace the circuit rather than swap parts blindly. You get a clear answer on what is wrong.
- 3
We give you a written price before any work starts. The quote covers the diagnosis, the parts, and the labor, and we settle it with you before we turn a bolt. No surprises on the bill. If we find something else while we are in there, we stop and talk to you first.
- 4
We make the repair and test it under load. We weld, realign, replace, and adjust, then run the gate through several full cycles and test the safety reversing system. The gate should close the way it did when it was new. Most jobs are finished in a single visit.
- 5
We back it in writing. Every completed repair carries our 90-Day Done Right Promise. If something we fixed is not right, we come back and make it right, no paperwork and no arguing. We will be there when we say, and we stand behind it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Mesquite?
A typical gate repair in Mesquite runs $150 to $450 depending on what has failed and how far the repair goes. A hinge or lock repair sits at the low end, around $150 to $250. A realignment or a weld and rust repair usually lands between $200 and $350. Electric and automatic gate repairs run $250 to $450 when a control board, limit switch, or safety sensor is involved, and an operator or gearbox replacement goes higher, from $450 to $900, because the parts cost more. Here is a rough breakdown of the common scenarios.

- Hinge and post repair: $150 – $300
- Gate realignment: $150 – $250
- Lock and access hardware repair: $150 – $275
- Weld and rust repair: $200 – $350
- Electric and automatic repair (board, limits, sensors): $250 – $450
- Operator or gearbox replacement: $450 – $900
What moves the price is the parts, the access to the gate, and whether the fault is simple or traced through a longer wiring run. You avoid overpaying by getting a written estimate before work starts and by not authorizing a parts swap without a clear diagnosis. Our free estimate includes the on-site diagnosis and a written price settled before we start, and we will give you a free second opinion on any written estimate you already have. Call (844) 797-2573 for an exact quote. Estimates are free.
Gate Repair Near Mesquite – Our Service Area
We repair gates across Mesquite and the surrounding communities, including Gate Repair in Bunkerville and Gate Repair in Moapa Valley over toward Moapa Town. Response times depend on the day and the distance, but most calls in and around Mesquite get scheduled quickly, and emergency calls are handled around the clock. If your gate is in a neighboring town, call and we will tell you honestly when we can be there. For our full range of repair work, see Gate Repair in Mesquite.
Serving Mesquite, NV – Our Local Coverage Area
We serve Mesquite and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Mesquite
Gate repair is the work of diagnosing and fixing whatever has stopped a gate from opening, closing, latching, or running safely. That can mean the motor and control board, the hinges and posts, the frame alignment, the locks, or the steel itself. Ironworks Gate Co. handles all of it, from a single worn hinge pin to a full operator replacement, so you do not have to call three trades to fix one gate.
Most gate repairs are finished in a single visit, usually within one to three hours of the technician arriving. Simple fixes like a hinge adjustment, a lock repair, or a sensor reset take under an hour. A weld repair or an operator replacement can take longer, and we will tell you the expected time when we quote. We come prepared, so you are not waiting on a second appointment.
Most repairs run between $150 and $450, with hinge and lock work at the low end and electric or automatic repairs toward the top. Operator or gearbox replacement can run $450 to $900 depending on the parts. Every price is quoted and agreed before any work starts, so there are no surprises on the bill. Call (844) 797-2573 for an exact quote, and remember the free second opinion on any written estimate you already have.
Yes, we service LiftMaster operators, along with DoorKing, Elite, Mighty Mule, and five other major brands. We are trained and equipped on LiftMaster control boards, limit switches, and safety sensors, so we can diagnose the fault and make the right repair the first time. If your gate runs a brand we have not named, call and describe it and we will tell you whether we can help.
Yes. A live person answers our phone 24 hours a day, 7 days a week, so a gate stuck open or a gate that won’t release gets a real conversation at any hour. We handle emergency repair calls around Mesquite and the nearby towns, and we will tell you honestly when we can be there. You do not have to wait until Monday morning to get help.
Every completed repair is protected by our written 90-Day Done Right Promise, the Keystone Standard we apply to every gate job. If something we fixed is not right within that window, we come back and make it right, with no paperwork and no arguing. It is written, it is straightforward, and it holds on every job. We stand behind it.
Clear the driveway so the technician can cycle the gate freely and reach both sides of it. Have the gate’s remote, keypad code, and any manual release key ready, and if you have a manual or paperwork for the operator, set it out. Tell us anything you noticed before the failure, like a new noise or a change in how the gate moved. That history helps us find the cause faster.
Schedule Your Gate Repair Service in Mesquite Today
If your gate is stuck, dragging, or refusing to latch, the fix is usually simpler than it looks. Call Ironworks Gate Co. at (844) 797-2573 and a live person will answer, day or night. We will schedule the repair, give you a written price before any work starts, and back the job with our 90-Day Done Right Promise. Free estimate, no obligation.
Written by the team at Ironworks Gate Co.