Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Mesquite Homeowners
A new driveway gate in Mesquite usually costs between $3,800 and $9,500 installed, depending on width, material, and whether you add an automatic opener. We plan every installation around your actual entrance, your soil, and the wind that funnels through the Virgin River corridor, so the gate swings true for years instead of sagging by the second summer. Our technicians bring up to 13 years of hands-on experience with welding, hinges, and gate automation, and they work to a written 90-Day Done Right Promise on every job. If your current gate is beyond saving, we’ll tell you straight. Call (844) 797-2573 and a live person will answer, day or night.

What Our Gate Installation Service Includes
Every gate we install is measured, set, and tested on site before we leave. We handle the posts, the welding, the hinges, and the automation together as one job, so nothing gets handed off between trades. Here is what each type of installation covers.
Driveway Gate Installation
The driveway gate is the one that carries the most weight and takes the most abuse. We size the posts and hinges for your span, align the gate to the slope of your concrete, and weld the frame so it holds its shape. If you want an opener, we set the operator and the safety edges in the same visit. Most Mesquite driveways need a gate built for sun and wind load, and we plan for both.

Pedestrian Gate Installation
A pedestrian gate is the walk-through gate beside your driveway, and it gets used more than any other gate on the property. We install self-closing hinges, latches that line up for years, and posts set deep enough to stay plumb. If you want a keypad or a lock that matches your driveway gate, we wire it in as part of the install.

Sliding Gate Installation
Sliding gates roll along a track instead of swinging out, which makes them a good fit where the driveway is short or the grade slopes. We set the track level and anchor it properly, because a sliding gate that runs off a poor track will bind within months. We also install the roller assemblies and the operator that matches the weight of the leaf.

Swing Gate Installation
Swing gates are the classic look, and they need the right hinge and post geometry to work without dragging. We check the opening, set the posts to the correct depth, and hang the gate so it clears the ground across its whole arc. If the ground slopes, we plan for that before we dig, not after.
Double Gate Installation
A double gate splits the opening into two leaves, which lets you cover a wide driveway without one heavy panel. We set both leaves to meet cleanly at the center and install the drop rod or the operator that keeps them aligned. On wider spans, we brace the frames so neither leaf sags over time.
Security Gate Installation
A security gate is built for controlled entry, often with a keypad, an intercom, or a call box at the driveway. We install the gate, the access hardware, and the wiring as one package so the reader and the lock work together. For homeowners who want to see who is at the gate before it opens, we set up the camera and the release on the same circuit.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Installation
We’re trained and equipped on nine gate-automation brands, and that range matters when your gate has to match an operator you already own or one you’ve picked out. On DoorKing systems, we know the access-control side well: the entry panels, the loop detectors, and how the operator ties into a keypad or a call box. DoorKing equipment is common on gated driveways where controlled entry matters, and we set it up so the reader, the release, and the gate all work together.
LiftMaster operators are another brand we work with regularly, and we know where their residential units wear and how to size one to your gate’s weight and travel. We also install and service Mighty Mule operators, which many homeowners choose for a single swing gate, and we match the unit to the leaf so it isn’t working harder than it should. Whether you have DoorKing, LiftMaster, Mighty Mule, or any other make, we can help.
Signs You Need Gate Installation Right Now
- Your gate drags or scrapes the ground. A gate that scrapes has usually lost its post alignment or its hinges have worn past adjustment. Left alone, it will chew through the latch and the operator, and the fix gets more expensive the longer you wait.
- The posts are leaning or the concrete is cracked. Leaning posts mean the footing has moved, often from soil settling or water. A gate hung on a moving post will never close right, and no amount of adjusting will hold it.
- The gate is rusted through at the joints. Rust at the weld points is the first sign the frame is giving out. Once the joints go, the gate loses its shape and the operator starts straining against a frame that’s no longer square.
- You’ve repaired the same problem twice this year. Repeat repairs on the same hinge, latch, or operator usually mean the gate itself is the problem. Replacing it once often costs less than chasing the same failure every season.
- You want controlled entry you don’t have. If your driveway is open to the street and you want a keypad, an intercom, or a gate that closes behind you, that’s a new installation, not a repair. We can plan the whole setup in one visit.
Our Gate Installation Process – Step by Step
- 1
We measure the opening and check the site. We look at the grade, the soil, and the concrete, and we confirm the gate width and the swing or slide direction. This is where most installation problems get avoided, so we take the time to get it right.
- 2
We give you a written price before any work starts. The quote covers the gate, the posts, the hardware, the operator if you’re adding one, and the labor. You’ll know the total before a single bolt is turned, and there are no surprises on the bill.
- 3
We set the posts and pour the footings. Posts go in at the correct depth for your soil, and we brace them while the concrete cures. A gate is only as good as its posts, so this step gets done properly or not at all.
- 4
We hang and weld the gate. We set the hinges, weld the frame, and check the gate through its full travel by hand before we touch the operator. If it doesn’t swing clean by hand, it isn’t ready for a motor.
- 5
We install the operator, test it, and walk you through it. We set the limits, the safety edges, and the access hardware, then run the gate through several full cycles. Before we leave, we show you how it works and hand you the written 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Mesquite?
What you pay depends on the gate’s size, material, and whether you add automation. Here are the ranges we see most often in Mesquite:

| Installation type | Typical installed price |
|---|---|
| Pedestrian gate (walk-through) | $1,200 – $2,800 |
| Single swing driveway gate | $3,800 – $6,500 |
| Sliding driveway gate | $4,500 – $7,500 |
| Double swing gate | $6,000 – $9,500 |
| Automatic opener (added) | $1,400 – $3,200 |
| Access control (keypad or intercom) | $600 – $1,800 |
Three things move the price most: the width of the opening, whether the ground needs work before posts go in, and how much automation you add. A wider gate needs heavier posts and a bigger operator, and a sloped driveway can add labor for the footings. You avoid overpaying by getting the plan right before the first post goes in, which is why we measure first and quote in writing. A free estimate from us includes the site check, the gate and hardware recommendation, and a written total. Call (844) 797-2573 and we’ll set it up.
Gate Installation Near Mesquite – Our Service Area
We install gates across Mesquite and the surrounding communities, including Bunkerville, Moapa Valley, and Moapa Town. Drive times from Mesquite are short, and we schedule installations and estimates so you’re not waiting all day for a crew. If you’re nearby and want a quote, we’ll get you on the calendar. You can also read more about our gate installation in Bunkerville and gate installation in Moapa Valley work.
Serving Mesquite, NV – Our Local Coverage Area
We serve Mesquite and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Installation in Mesquite
Gate installation is the full job of setting new posts, hanging a gate, and adding an operator or access hardware if you want one. It covers the welding, the hinges, the automation, and the testing, done as one project. We handle the whole scope so the gate and the opener are sized to work together from the start. Call (844) 797-2573 if you want to talk through what your entrance needs.
Most single-gate installations take one to two days once we’re on site, and wider double gates or automated setups can take two to three days. The timing depends on the footings, the gate size, and whether we’re adding access control. We give you a realistic schedule with the written quote so you can plan around it. Call (844) 797-2573 to get a date on the calendar.
Pedestrian gates run about $1,200 – $2,800 installed, and driveway gates run $3,800 – $9,500 depending on width and material. Adding an automatic opener is roughly $1,400 – $3,200 more, and access control adds $600 – $1,800. Every price is quoted in writing and agreed before any work starts. Call (844) 797-2573 for a free estimate.
Yes, we install and service LiftMaster operators as part of our gate installation work. We’re trained on nine gate-automation brands, including LiftMaster, DoorKing, and Mighty Mule, so we can match the right unit to your gate. If you already have a LiftMaster operator, we’ll check it against the new gate before we install. Call (844) 797-2573 to talk through your setup.
Yes. A live person answers our phone 24 hours a day, 7 days a week, so you’re not stuck in a voicemail queue if a gate fails and won’t close. For repair and emergency calls we move as fast as we can, and most jobs are finished in a single visit. Call (844) 797-2573 and we’ll get someone out.
Every installation is covered by our written 90-Day Done Right Promise. If something isn’t right, we come back and make it right, with no paperwork and no arguing. It’s the same standard we put on every job, whether it’s the first gate we’ve hung for you or the tenth. Call (844) 797-2573 and we’ll explain what’s covered.
Clear the driveway and the area around the gate opening so the crew has room to work, and make sure we can reach the gate from the street. If you have an existing gate or operator, leave it in place until we arrive so we can see how it was set up. We’ll handle the rest, including the old gate if it needs to come down. Call (844) 797-2573 if you have questions before the day.
Schedule Your Gate Installation Service in Mesquite Today
If your gate needs replacing, or you’re ready to add an automatic gate to your driveway, call Ironworks Gate Co. Mesquite at (844) 797-2573. You’ll get a free, no-obligation estimate, a written price before any work starts, and a 90-Day Done Right Promise on the finished job. A live person answers every call, 24 hours a day. Ask about the $50 off any repair over $250 and the 5% senior and veteran discount.
Written by the team at Ironworks Gate Co.