Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Welding & Fabrication in Mesquite: The Owner’s Guide
Welding and fabrication on a Linear gate system in Mesquite typically runs $275 to $850 for a single repair, and most of those repairs are finished in one visit the same day you call. We cut, fit, and weld broken hinges, cracked posts, bent frames, and failed operator mounts, then we make sure the Linear arm, motor, and limits still line up with the rebuilt gate. The price is settled before a single bolt is turned.

Owners usually find us the same way. The gate sags a quarter inch, then an inch. The Linear operator strains at the end of a cycle, or it reverses for no reason. Someone looks at the hinge and sees rust bleeding through the powder coat, or a weld that’s been letting go for a while. In Mesquite, the wind does the rest.
Which Linear Models This Applies To
Linear swing and slide operators – the LCR, LCO, LSO, and their older SW-series swing siblings – all mount to a gate frame we can repair or rebuild. The operator itself is fine in most of the calls we run. The gate is the problem: a welded hinge that pulled, a post that tilted with the soil, a frame that’s been flexing under load for years.
To match the right fix, start with the label on the operator housing (the model number is usually on a plate near the manual release keyhole) and measure your gate leaf. Linear’s swing arms are load-rated by leaf weight and leaf length, and the specs on a 12-foot, 300-pound leaf are different from those on an 8-footer. If the number’s worn off, a photo of the operator and a measurement of the gate tells us plenty.
On the OEM-versus-aftermarket question, Linear’s own replacement parts (hinges, brackets, arm assemblies) are the safe fit when the part number is known. For fabricated parts – hinges, posts, gate frames, mounting saddles – there’s no OEM version at all, because these are made to fit the gate, not the motor. That’s where fabrication matters. We build the part for your gate. We don’t carry parts on a truck or stock them locally, so we measure, order, and schedule. Ironworks Gate Co. Mesquite is an independent service provider – not affiliated with Linear.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Linear Welding & Fabrication Is Failing
- The gate sags at the hinge side. Most often a weld crack at the hinge plate or a hinge pin that’s worn oval. The Linear operator keeps working harder, which is why the motor’s failure often follows the gate’s.
- The operator arm runs out of travel, or reverses. A sagging gate throws off the arc the Linear arm expects. On slide operators, a bent track supports the same symptom.
- A visible crack in the gate frame or post weld. Mesquite’s swings reach 40 to 60 mph on a bad day, and a gate that flexes constantly will crack at a weld seam. Once it’s cracked, the gate is running on the operator instead of the frame.
- Rust around a hinge or post base. The oxidation starts inside the weld, not on top of it. By the time it’s visible, the weld has lost strength.
- The operator mount has moved or the bracket is loose. Wind and soil movement walk a gate post out of plumb. The Linear box stays bolted, but the geometry it was set to has changed.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Welding and fabrication pricing in Mesquite runs in three tiers. Hinge repairs and re-welds land around $275 to $425. A rebuilt gate frame or a fabricated post saddle is $425 to $650. Full-line gate rebuilds (a 12- to 16-foot leaf with multiple hinges, cross-bracing, and re-hanging) start around $650 and go up from there. The number you’re quoted is the number you pay. It’s quoted and agreed before any work starts – no surprises on the bill.
What drives the range: leaf weight and size, how far the gate has to come off its post, whether the post needs resetting (that’s concrete and soil work, not just welding), and whether we have to fabricate a fresh part or repair what’s there. Every job is covered by our written 90-Day Done Right Promise – if it’s not right, we come back and make it right. No arguing. No paperwork.
DIY or Call Us?
Here’s the honest split. A homeowner can safely check the gate for cracks and rust, look at the operator label, measure the leaf, and confirm the manual release works. That’s useful information and it saves time on the phone.
Where DIY goes wrong is at the weld itself. Welding a gate hinge or post saddle is high-tension work on a heavy leaf – a 300-pound gate that fails in the middle of a repair is genuinely dangerous. The wrong heat or a weak arc leaves a crack that looks fixed and breaks a month later. And without the gate plumb and the geometry re-set, the Linear operator will start straining again the same day you finish. This is work for a trained technician. Call our team at (844) 797-2573 – the second opinion on any written estimate is free.
FAQs
A properly welded hinge on a powder-coated frame should last 10 to 15 years in Mesquite’s climate. The reality is closer to 6 to 10 when the gate swings every day, gets baked by summer heat, and catches the spring wind. Sun is hard on the finish, and once the coating fails, the weld is the next to go.
Yes. Nine times out of ten, we repair rather than replace. We grind the old weld out, clean the steel, re-weld, re-coat, and re-hang the gate on the operator geometry. A full gate replacement is rare – usually only when the frame has cracked in three or four places.
Most single-hinge or single-weld repairs are done in one visit, usually 2 to 4 hours. A full gate rebuild is scheduled and typically runs one long day. You’ll know the schedule when we quote it.
Linear-specific replacement parts come from Linear-approved distribution when the model number is confirmed. Fabricated parts are measured, drawn, and built to fit your gate – not a stock part from a shelf. That’s why we measure first and schedule the work rather than trying to make the wrong part fit the same day.
Call Ironworks Gate Co. Mesquite at (844) 797-2573 for a free estimate. We’ll talk through the symptom, confirm the Linear model, and give you a price before any work starts. Background-checked technicians. 90-Day Done Right Promise on every job. Standing offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. We also service LiftMaster, Mighty Mule, and Ghost Controls.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.