Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Motor Replacement: The Mesquite Owner’s Guide
Linear gate motor replacement in Mesquite typically runs $650 to $1,400 installed for a residential slide or swing operator, and most jobs are done in a single visit once the replacement motor is matched to your existing Linear unit. Same-day emergency availability is available when a gate is stuck open and the driveway isn’t secure. You’ll know the motor is on its way out when the gate starts reversing mid-travel, the operator runs longer than it should, or the control board clicks but the arm won’t move.

In Mesquite, the pattern tends to arrive in July and August. We see Linear motors that sounded fine in April start tripping the thermal overload by mid-summer, because the operator is running hotter than the ambient air and the capacitors inside have dried out. Once that begins, cleaning the track or adjusting the limit switches buys you a few weeks. It doesn’t fix the motor.
Key Takeaways
- Installed Linear motor replacement typically runs $650 to $1,400 in Mesquite.
- We match the replacement to the specific Linear model on your gate, not a generic substitute.
- Capacitor drift and control board failure are the two most common failure points on older Linear units.
- The written price is agreed before any work starts, and every job carries our 90-Day Done Right Promise.
- Ironworks Gate Co. Mesquite is an independent service provider. We’re not affiliated with Linear.
Which Linear Models This Applies To
Linear makes residential and light-commercial slide and swing operators, and the replacement motor you need depends on which family is on your gate. The most common residential units we see in Mesquite are the slide operators in the LDO and LSO families, and the swing operators in the SW and ASW families. A few homes here are running older Linear units that predate current production, and those can be matched by reading the data plate on the operator housing, not by eyeballing the arm.
Here’s the compatibility gotcha most owners run into: Linear changed control-board architecture across model generations, and a replacement motor from a different generation will not talk to your existing receiver, keypad, or safety edge. If the gate has a plug-in radio receiver, the replacement board has to use the same frequency and the same accessory harness, or you’re replacing the whole control package, not just the motor. We check the data plate and the harness before quoting, so what we order is what fits.
On the OEM-versus-aftermarket decision: Linear-branded replacement motors are the surest fit, and we generally recommend them when the existing unit is recent enough that the rest of the assembly is in good shape. Quality aftermarket equivalents exist for older out-of-production units, and on a gate from the mid-2000s, an aftermarket motor paired with a new control board is often the better dollar. We’ll tell you which option makes sense for your gate, and we’ll show you why.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Linear Gate Motor Replacement Is Failing
Linear motors rarely fail without warning. The signs show up weeks or months before the gate stops moving:
- The gate reverses mid-travel or stops partway. On a Linear operator, this usually means the current-sensing circuit is reading resistance that isn’t there, either from a weak motor winding or a failing board. Adjusting the sensitivity setting won’t fix a motor that’s actually losing torque.
- The motor hums but the gate doesn’t move. That’s the classic signature of a failed start capacitor, common in Mesquite’s heat because capacitors dry out faster when the operator runs hot. A capacitor swap is cheap. If the winding is also degraded, a new motor is the honest answer.
- The operator runs past the limit switch. Worn limit cams or a misaligned limit nut will let the gate push past its stop point. That’s a mechanical issue on the operator, and if it’s combined with an aging motor, the practical replacement is the whole operator head.
- Clicking from the control board with no movement. A relay or board failure. This is the one case where the motor might still be good and the repair is board-only, which is why we check before quoting a motor.
- The gate feels sluggish on cool mornings and fine by afternoon. Motor bearings and lubricant in the gearbox are degrading. It works until it doesn’t, and it usually doesn’t on a Sunday.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a residential Linear slide or swing operator replacement in Mesquite, the installed price typically runs $650 to $1,400. The range comes down to three things: which Linear model your gate uses, whether the control board and receiver are being replaced along with the motor, and whether the gate itself needs any mechanical work (worn rollers, a bent track, a hinge that’s drifted).
| Line item | Typical range |
|---|---|
| Replacement Linear motor and operator head | $380 – $750 |
| New control board and receiver (when required) | $120 – $280 |
| Labor, install, and re-setup of travel limits | $180 – $320 |
| Gate-side mechanical adjustments (rollers, track, hinges) | $60 – $180 |
The price is quoted and agreed before work starts. Warranty on our labor is the 90-Day Done Right Promise, in writing, no arguing: if it isn’t right, we come back and make it right. The motor itself carries whatever the manufacturer’s warranty is on the part.

If you have a written estimate from another shop on Linear replacement work, we’ll give you a free second opinion on it. We’ll tell you straight whether the scope is right.
DIY or Call Us?
There’s a short list of things you can safely check yourself. Read the data plate on the Linear operator and write down the model number. Test the manual release to see if the gate moves freely by hand. Look at the track for debris and the rollers for flat spots. That’s where it ends.
What we don’t recommend: pulling the motor out of a Linear operator head, replacing a control board live, or swapping a capacitor on a unit that’s still connected to power. The 120-volt feed to that operator is not something to touch unless you know what you’re doing, and we’ve seen more than one gate come in with a homeowner-started repair that turned a $650 job into a $1,400 one. This is one to hand off.
Call (844) 797-2573. We’ll tell you on the phone which Linear model you’re running and whether the motor needs replacing or just the board.
FAQs
Realistically, eight to twelve years on a residential Linear operator in this climate. The heat is the deciding factor: motors that run in direct afternoon sun here fail noticeably faster than shaded units, and a unit that’s undersized for the gate weight will go in six or seven years. Routine tune-ups stretch that, but nothing makes the heat disappear.
Yes, sometimes. A failed capacitor, a bad control board, or a misaligned limit switch are all repairable, and on a Motor that’s otherwise healthy, that’s the cheaper call. We check the board and the motor winding separately before we quote a replacement, because on roughly a third of the Linear calls we run in Mesquite, the motor itself is fine and the board is the problem.
A straight motor swap on a residential Linear operator is typically two to three hours, including travel-limit setup and testing. If we’re also replacing the control board and receiver, add about an hour. Most jobs are finished in a single visit.
We order it to the model on your data plate through authorized automation suppliers. We don’t carry Linear parts on a truck, and we won’t tell you we do. What we do is specify the right part for your unit and have it in hand before we arrive.
If you have a Linear, LiftMaster, Mighty Mule, or Ghost Controls operator on your gate, we service it. Ironworks Gate Co. Mesquite specializes in driveway and estate gates: repair, installation, motors and openers, access control, and gate-side welding. Our technicians have up to 13 years of experience, and every job is backed in writing. Call (844) 797-2573 for a free estimate. We pick up live, 24 hours a day, seven days a week.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.