Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Welding & Fabrication: The Mesquite Owner’s Guide
We repair and fabricate Ghost Controls-compatible gate hardware in Mesquite, and most welding and fabrication jobs on a residential Ghost Controls gate run $285 to $760 installed, depending on whether we’re re-welding an existing bracket or building a new mount for a heavier arm. Straightforward bracket and hinge repairs are often finished the same day you call. We’re an independent service provider, not affiliated with Ghost Controls, but we’re trained on the brand and we know its arms, mounts and pivot hardware well.

Owners usually find this problem the same way. The gate still moves, but it starts to drag at one end, or the arm pulls away from a post that’s working loose, or a weld on the mounting plate cracks after a few summers of Mesquite heat. Sometimes it’s a hinge post that’s shifted a half-inch in caliche soil, and the opener is doing the work of holding the gate up instead of just swinging it. By the time you notice the noise or the wobble, the weld has usually been failing for a while.
Which Ghost Controls Models This Applies To
Ghost Controls builds its residential line around a handful of arm-style openers, and the mounting and welding side of the work applies across all of them. The single-arm models most Mesquite homeowners have (the AR and TSS-style units sold for single-swing gates) mount to a post bracket and an operator arm bracket, and both are welded or bolted to your existing gate frame and post. The dual-arm setups push heavier gates and put more stress on those mounts. If you’re not sure which you have, look at the label on the control box or the arm housing, or measure the arm’s fully extended reach and compare it against your gate’s width. What matters for fabrication is the geometry, not the model name: post spacing, the height of the arm’s pivot point, and how your gate’s frame is built.
Here’s the OEM-versus-aftermarket decision that catches people. Ghost Controls sells replacement brackets and arms as its own proprietary parts, and aftermarket universal brackets exist, but they don’t always match the arm’s pivot height or the hole spacing Ghost Controls uses. A universal bracket that’s 3/8 inch off in pivot height will make the arm bind and can shorten the motor’s life. For a Ghost Controls gate in Mesquite, when the original bracket is salvageable we repair the weld; when it isn’t, we match the replacement to the existing arm geometry rather than force a universal fit. If you own a LiftMaster, Mighty Mule or DoorKing gate instead, we work on those brands too.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Welding & Fabrication Is Failing
Weld and bracket failures announce themselves before they strand you. Watch for these:
- Visible cracks or rust lines at the weld. A dark line or hairline crack along a bracket weld usually means the weld is fatiguing, often from a gate that’s out of alignment and pulling on the mount.
- The arm pulls away from the post or gate. A loose or cracked bracket lets the operator arm shift under load, and the opener works harder every cycle until it stalls or faults.
- The gate drags or sags at the latch end. That’s frequently a hinge post that’s moved, not the opener. The weld work has to bring the gate back to level, not just shore up the bolt.
- Grinding, popping or a sudden hesitation. These point to a mounting plate that’s flexing where it shouldn’t, or an arm bracket that’s shifted and is now binding against the frame.
- Rust bloom around a weld after the rainy season. Mesquite’s dry climate hides it, but the wetter months and irrigation overspray at the gate line can rust a marginal weld from the inside out.
One reality about the region: caliche soil and summer heat both work against gate hardware here. Posts move, welds fatigue, and a mount that was fine in a cooler climate has to survive 110-degree swings.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Mesquite depends on what we’re actually doing. A simple bracket re-weld or hinge repair typically lands at the low end. Rebuilding a mounting plate, aligning a shifted post, or fabricating a custom arm bracket for a heavier gate pushes toward the high end. We quote the price before any work starts and put it in writing, so the bill matches the number you agreed to.

- Bracket or hinge re-weld: typically $285 to $425 installed
- New mounting plate fabrication and alignment: roughly $375 to $560 installed
- Custom arm bracket for a heavier gate: around $480 to $760 installed
Those ranges cover parts and labor together. We don’t carry stock, so if a Ghost Controls-specific bracket has to be ordered, we’ll tell you the lead time up front. Every job is protected by our 90-Day Done Right Promise: if the work isn’t right, we come back and make it right, in writing, no arguing. There’s a $50 Off Any Repair Over $250 standing offer, and a free second opinion on any written estimate you already have.
DIY or Call Us?
You can safely check a few things. Look for visible cracks or rust at the welds, wiggle the arm to see if the bracket has play, and check whether the gate hangs level with a level or a tape measure corner to corner. What you shouldn’t do is weld a cracked bracket or mounting plate yourself while it’s still holding the operator arm. Welding on or near a gate frame carrying a live opener is a genuine way to damage the control board, and arc welding on structural gate hardware is work that should be done by someone trained on it. A bad weld under a gate that swings can also let the gate drop. That’s the part we’d rather you not risk.
If you’re seeing cracks, wobble, or an arm that’s pulling loose, it’s worth a look before it strands you. Call us at (844) 797-2573 and we’ll give you a straight answer and an upfront price.
FAQs
Done correctly, a repaired or fabricated bracket on a residential gate typically holds for years, and often outlasts the original factory weld. The bigger variable is alignment: if the gate frame stays square and the post doesn’t shift, the weld does its job. A gate that’s out of alignment will fatigue even a good weld over time, which is why we check alignment as part of the repair. Call (844) 797-2573 if you want us to assess yours.
Often, yes. If the metal around the weld is still sound, we can grind out a cracked weld and re-weld the bracket rather than fabricate a new one, which usually costs less. If the plate is rusted through or the bracket has deformed, replacement or fabrication is the honest answer. We’ll tell you which one it is before we start.
Most bracket and hinge repairs are done in a single visit, often within a couple of hours, and we complete most jobs on the first trip. If a Ghost Controls-specific part has to be ordered, the timeline depends on the supplier, and we’ll give you an honest lead time when we quote. Alignment work takes a little longer because we check the whole gate, not just the weld.
We match the replacement to your specific arm geometry rather than forcing a universal bracket, and when a Ghost Controls proprietary bracket is the right fit, we order it. We’re trained on nine gate-automation brands, so we know how Ghost Controls brackets differ from a LiftMaster or Mighty Mule mount. We don’t keep parts on a truck; we quote the part and the labor together before any work begins.
Call (844) 797-2573 for a free estimate, and a live person will answer, day or night.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.