Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Welding & Fabrication: The Mesquite Owner’s Guide
We handle FAAC welding and fabrication for Mesquite gates, and most fabricated repairs run $340 to $780 installed depending on how much steel has to be cut out and replaced, with emergency weld-and-stabilize work available the same day. If a post is pulling away from the gate leaf, a hinge bracket has torn its mounts, or a box-frame section has gone soft with rust, this is the repair that keeps a gate hanging straight instead of dragging. Owners in Mesquite usually find this problem at the worst moment: the gate sags a half-inch, the motor strains to push it, and then one morning it stops halfway open with the operator humming and the leaf going nowhere.

Which FAAC Models This Applies To
Fabrication work isn’t model-specific the way a motor or a control board is, but the mounting does depend on the FAAC operator bolted to your gate. The common residential lines around Mesquite are the FAAC 391, 400, 402, 422, 740, and 844, plus the S418 and C721 for sliding and heavier swing leaves. Swing operators bolt to a mounting bracket or a post plate, sliding operators ride a rack welded to the gate frame, and both put load on the steel that holds them. The cast brackets and welded tabs that FAAC supplies are built to a size, and cutting or welding near them changes the geometry the operator was set up for.
To identify what you have, read the label on the operator housing, then measure the gate leaf, the distance from hinge to hinge, and the mounting plate spacing. Write those down before you call anyone. Original FAAC brackets are the safest match when they can be found in stock, but a good fabricator can make a correct replacement from the measurements and the mounting pattern. Aftermarket fabricated parts are only as good as the steel and the fit, so the spec that matters is thickness and weld quality, not the label.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Welding & Fabrication Is Failing
Steel fails slowly and then all at once. Here’s what the failure looks like before it shows up as a dead gate.
- A gate that sags at the hinge side. The weld or bracket holding the hinge has cracked, and the load has shifted onto the operator. Left alone, it overloads the motor.
- Rust bleeding from a weld seam. Water sits in the joint, the weld thins from the inside, and the section loses strength before you see a break. In Mesquite’s dry air this happens slower than in wet climates, but irrigation overspray and low-lying damp spots speed it up.
- The operator runs but the gate barely moves. The mounting plate or rack has warped or pulled loose, so the motor is pushing against steel that is no longer aligned.
- A grinding or popping noise at the post. A welded tab or anchor is cracking under load.
- Visible rust creeping across the gate frame. Frame sections thin out until they will not hold a hinge, an operator bracket, or a rack.
If more than one of these is showing, the gate is past a cosmetic touch-up. Call it in.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Fabrication pricing in Mesquite depends on the job, so here’s the honest breakdown. A straightforward weld repair, re-anchoring a post or a torn bracket, runs about $340 to $480. A fabricated replacement section that requires cutting out failed steel and welding in new runs $520 to $780. New hinge plates, repaired rack mounts, and re-hung gate leaves sit in that range too.
Three things drive the number: how much steel has to come out, whether the gate needs to be taken off its hinges, and whether the operator has to be disconnected and re-aligned afterward. Labor and parts are quoted as one upfront price, settled before a single bolt is turned. The welding itself is protected by our 90-Day Done Right Promise, written and no-hassle. If the steel isn’t right, we come back and make it right.
DIY or Call Us?
Some of this you can check safely. Look for cracks or rust streaks at the welds, wiggle the gate leaf by hand to feel for play, and confirm the operator bracket hasn’t pulled loose. If it’s a loose bolt you can tighten with a wrench, do it.
Welding is a different matter. Arc welding on a driveway gate means live electrical current, hot steel, and fire risk, and welding near the FAAC operator can damage the motor or its control board if it isn’t isolated correctly. The gate weighs a few hundred pounds and will be swinging or sliding while you’re working under it. That’s not a job for a homeowner. Our technicians have up to 13 years of experience with these gates, and they can tell a structural failure from a cosmetic one in minutes.
We service FAAC along with LiftMaster, Mighty Mule, and Ghost Controls, so the right fix is made on the first visit. Call (844) 797-2573 for a free estimate. We’ll give you an upfront price before any work starts.
FAQs
How long does a FAAC fabrication repair last?
With proper galvanized or painted steel, a good weld repair on a FAAC gate will last for years. Cracks come back when the underlying load problem wasn’t fixed, which is why we check the gate’s alignment and the operator’s settings, not just the break.
Can it be repaired instead of replaced?
Usually yes. Most failed FAAC gate steel can be welded or re-bracketed, and full gate replacement is rarely necessary unless the frame is rusted through in several places. We’ll tell you honestly if the steel is too far gone.
How long does the swap take?
A single weld repair is typically a couple of hours, and a larger fabricated section usually fits in one visit. If the operator has to be disconnected and re-aligned, plan on most of a morning.
How do you source the part?
We measure your gate and mounting pattern, identify the FAAC model on the operator label, and fabricate or source the bracket or section to match. Mesquite isn’t a big supply town, so we order right the first time rather than guess.
Call (844) 797-2573 for a free estimate. A live person answers 24 hours a day.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.