Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Hinge & Roller Replacement: The Mesquite Owner’s Guide
We install FAAC-compatible hinges and rollers on driveway and estate gates throughout Mesquite, and most single-hinge or roller swaps run $180 to $340 installed, with more involved hinge sets and gate-side repairs landing between $340 and $650. Many Mesquite jobs are completed the same day you call, and you’ll have a firm, upfront price settled before we touch a bolt. Higher-end actuator replacements are always quoted first, and no work begins until you agree to the number.

Owners usually discover the failure the same way. The gate starts to sag or drag near the latch, the roller squeals through its travel, or the hinge pin backs out and the gate hangs a half-inch low. Sometimes a weld cracks at the hinge plate and the gate leans against the stop. In every case, the part is telling you it’s done, and the longer you run it, the more stress it puts on the operator and the frame.
Which FAAC Models This Applies To
FAAC builds several lines of swing and sliding operators, and the hinge and roller hardware differs between them. The 390, 391, 400, and 402 series are common on residential swing gates, while the 740 and 750 lines show up on heavier estate gates and sliding applications around Mesquite. The right hinge and roller depends on your gate weight, the number and size of leaves, the post material, and the operator’s rated capacity, not just the model number on the arm.
To identify the correct part, check the label on the operator housing or control box for the model and serial number, then measure the gate leaf width, height, and approximate weight. Photograph the existing hinge plate and roller bracket from two angles, including any stamping or casting marks. FAAC uses specific pin diameters and plate bolt patterns, and a generic hardware-store hinge will not line up with the factory bolt holes without drilling, which weakens the post and shortens the life of the repair.
On the OEM-versus-aftermarket question, we’re straightforward about it. FAAC original parts fit exactly and match the factory tolerances. Quality aftermarket equivalents cost less and perform well for many residential gates, provided the pin diameter, plate thickness, and load rating match your model. We source the right part for your gate and tell you plainly which route we recommend and why. Ironworks Gate Co. Mesquite is an independent service provider and is not affiliated with FAAC.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Hinge & Roller Replacement Is Failing
Hinge and roller wear rarely happens overnight. It shows up in small ways and gets worse. Here’s what we look for on a Mesquite gate:
- The gate sags at the latch side. Worn hinge pins and elongated bolt holes let the leaf drop, so the gate no longer meets the strike cleanly. Left alone, the operator works harder to close it, and the motor takes the load the hinge should be carrying.
- The roller squeals or grinds through its travel. Sealed bearings dry out and grit works its way into the track. The noise is the metal telling you it’s dry, and eventually the roller flat-spots and the gate shudders as it moves.
- The gate drags on the ground or binds mid-swing. A worn hinge or roller that’s out of alignment throws the leaf off its arc. The operator strains to compensate, and the gate hesitates or reverses partway through the cycle.
- The hinge plate is loose at the post. Bolts work loose over time, and a cracked weld at the hinge plate shows as a fine line of rust or a wiggle when you push the gate. This one needs attention before the gate drops.
- The operator keeps reversing or faulting. A binding gate forces the operator to fight resistance it wasn’t designed for, and the control board reads that as an obstruction. What looks like an operator problem is often a hinge or roller problem underneath it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Mesquite, a single FAAC-compatible hinge or roller replacement typically runs $180 to $340 installed. A full hinge set on a two-leaf swing gate, or a job that also needs welding at a cracked hinge plate, runs $340 to $650. Heavy gates, custom brackets, or a repair that also needs operator realignment sit at the top of that range. Everything in between gets quoted to your gate, not to a flat rate on a card.

Here’s what’s in the number: the part, the labor, and the hardware. There’s no separate diagnostic fee hidden in the total. The price is quoted and agreed before any work starts, and if we find something else wrong while we’re in there, we tell you and re-quote before proceeding. Our work is backed by the written 90-Day Done Right Promise, the Keystone Standard: no paperwork, no arguing. If the repair isn’t right, we come back and make it right. Current standing offer: $50 Off Any Repair Over $250.
DIY or Call Us?
Some checks are safe to do yourself. Look at the gate from the side and note whether the leaf hangs even or drops at the latch. Push gently on each hinge plate to see if it moves independently of the post. Run the gate by hand with the operator disengaged and listen for the roller or hinge, which is where you’ll usually find the trouble. Those inspections tell you a lot, and they’re safe.
Where DIY goes wrong is in the installation. An unrated hinge or a roller with a mismatched pin diameter can fail under load and drop a gate leaf, and that’s a serious risk near the operator and the driveway. This isn’t high-tension spring work, but a heavy gate swinging off a failed hinge is dangerous, and no homeowner should find that out the hard way. We’d rather hang it right the first time. Call (844) 797-2573 and we’ll take a look.
FAQs
How long do FAAC hinges and rollers last in Mesquite? In our experience, most FAAC hinge and roller assemblies last 7 to 12 years on a residential gate in Mesquite’s climate. The heat and dust here dry out bearings and accelerate wear on bushings, so gates that swing constantly or carry heavier loads tend to reach the end of that range sooner.
Can a failed hinge or roller be repaired instead of replaced? Sometimes, yes. A dry bearing or a loose bolt can often be serviced and the gate brought back into line. But when the pin is worn or the plate is cracked, replacement is the right call, and a re-tightened worn part will fail again within months. We’ll tell you which one your gate actually needs.
How long does the swap take? A single hinge or roller replacement usually takes one to two hours on site. A full hinge set or a job that also involves welding takes longer, and we’ll give you a realistic window when you book. Most Mesquite jobs are completed in a single visit.
How do you source the FAAC part? We source FAAC-compatible hardware matched to your model and gate weight, choosing between factory parts and quality aftermarket equivalents based on fit, rating, and value. We tell you which route we’re taking and why before we order. Call (844) 797-2573 for a free estimate.
We also service LiftMaster, Mighty Mule, and Ghost Controls gates, so whatever is on your driveway, we’re trained on it. If your gate is dragging, sagging, or squealing, call Ironworks Gate Co. Mesquite at (844) 797-2573 for a free estimate. A live person answers, 24 hours a day, and every job is backed in writing by the 90-Day Done Right Promise. Seniors and veterans always get 5% off, and we’ll gladly give you a free second opinion on any written estimate you’ve already got.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.