Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Parts & Welding in Mesquite: What to Know First
We provide independent FAAC gate parts and welding in Mesquite, and most FAAC swing and barrier repairs we see are finished in a single visit once we’ve confirmed the right parts. FAAC is an Italian brand with several generations of control boards and operator arms in the field, so the honest answer on price is that it depends on which series you own and what has actually failed – we diagnose first, quote in writing, and the price is agreed before a single bolt is turned. This page is for the homeowner with a FAAC arm or barrier operator on the driveway who wants it fixed properly rather than replaced on a guess. Call (844) 797-2573 and a live person answers, day or night.

How FAAC Products Fail – and How We Fix Them
FAAC equipment fails in its own particular ways, and knowing those patterns is most of the job. Here is what we actually find on Mesquite driveways.
- Worn arm pivots and clevis pins on 400 and 390 series swing operators. The die-cast arms develop play at the pivot after years of cycles, so the gate sags and the arm strains against the post. Owners often blame the motor. We weld and re-bush the mounting bracket, replace the worn pin, and reset the arm geometry so the operator runs true again rather than fighting a bent gate.
- Control board failures after our summer heat. Mesquite regularly runs above 110°F, and the enclosures on older FAAC boards bake in direct sun. We see cracked solder joints and blown capacitors on the 740 and 844 series boards that would run for years in a cooler climate. We test the board in place before condemning it, then fit an OEM board or a quality aftermarket equivalent, whichever is the right call for your unit’s age.
- Hinge and post corrosion from the Virgin Valley’s hard water and dust. Sprinkler overspray and wind-blown alkaline dust pit steel hinges and gate posts faster here than most owners expect. When we re-weld a hinge, we grind back the rust properly and finish the weld so it holds. A quick tack over rust will fail inside a season.
- Battery backup and solar-charge faults on solar FAAC operators. FAAC solar setups with panel and battery backup are common on outlying Mesquite properties. When the gate slows or stops after dark, it’s usually a tired battery or a charge controller that’s quit, not the operator itself. We test the charging circuit and replace the battery before anyone talks about a new motor.
- Sagging gate leaves that wore out the operator. On heavy FAAC swing gates, the real fault is often a dropped hinge or a post that has shifted, and the operator has been dragging a gate it was never built to lift. A FAAC motor on a binding gate will fail early, every time. We repair the hinge or reset the post, weld the leaf back to square, and only then confirm the operator is healthy.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our FAAC Gate Parts & Welding Process
Every FAAC job follows the same order, whether it’s a hinge repair or a full arm replacement.
- 1
Diagnose on site. We run the gate, watch the arm through a full cycle, test the board and check the mounting and hinges. We’re looking for the cause, not just the symptom.
- 2
Make the parts decision with you. We explain what failed and lay out the options: OEM FAAC parts where the unit is newer and still under warranty, or a quality aftermarket equivalent where it makes better sense on an older operator. We never fit a part that would void a manufacturer warranty without telling you first.
- 3
Quote in writing. The price is settled and agreed before we touch a bolt. No surprises on the bill.
- 4
Do the repair. Welding, hinge and bracket work, board or arm replacement, all on the same visit wherever the parts allow.
- 5
Test the full cycle. We cycle the gate repeatedly, check the safety edges and reversing, and confirm the operator runs without strain.
- 6
Back it in writing. Every job is covered by our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat FAAC Gate Parts & Welding Costs in Mesquite
Here’s what the common FAAC jobs typically run in the Mesquite market. These are real ranges, and your written quote is what you’ll pay.
| Job | Typical range |
|---|---|
| Hinge replacement / re-weld | $250 – $475 |
| Post repair or reset | $350 – $850 |
| Gate rollers and track work | $180 – $400 |
| Latch and lock repair | $150 – $325 |
| Custom welding (rail, arm, bracket) | $200 – $650 |
| FAAC control board or operator arm | $450 – $1,200+ |
What moves the price is the parts tier (OEM against aftermarket), post condition, and whether the gate itself needs to be re-hung before any operator work is worth doing. We quote every job free and settle the price before work starts. Call (844) 797-2573 for your written estimate.

Why Mesquite Homeowners Call Ironworks Gate Co. Mesquite for FAAC Work
FAAC is one of nine gate-automation brands we’re trained and equipped on, alongside LiftMaster, Mighty Mule, Ghost Controls, DoorKing, BFT, Linear, Viking and Elite, so we make the correct diagnosis on the first visit rather than ordering parts on a guess. We work as an independent FAAC service provider, not affiliated with or authorized by the manufacturer, and we’ll tell you plainly which parts make sense for your unit. Every job is backed by our written 90-Day Done Right Promise, and our background-checked, uniformed technicians treat your home the way they’d treat their own mother’s. A live person answers the phone 24 hours a day, and our technicians bring up to 13 years of experience to the work. We also offer $50 off any repair over $250 and a free second opinion on any written estimate.
FAQs
Not when the repair is done with the right parts and methods. We ask about your operator’s age and warranty status before recommending anything, and where a unit is still covered we lean toward OEM FAAC parts to protect it. As an independent FAAC service provider we aren’t tied to the manufacturer, so our recommendation is about your gate, not a sales target.
Usually yes. FAAC has kept good parts support across its swing and barrier lines, and where a specific OEM part is discontinued we source a quality aftermarket equivalent and tell you that’s what we’re fitting. If neither is available, we’ll walk you through your options honestly rather than leave you guessing.
Repair it if the board, arm or hinges are the fault and the operator is otherwise sound – most FAAC repairs we do are worth it. Replace only when the operator is old enough that repairs start stacking up. We’ll give you both numbers and a straight comparison, and the decision is yours.
We prioritize gates stuck open, since that’s a security problem. Call (844) 797-2573 and a live person answers 24 hours a day, and we’ll get a technician out as soon as we can – often same day for urgent repairs in Mesquite.
Yes. Every completed job is covered by our 90-Day Done Right Promise – a written, no-hassle guarantee. If something isn’t right, we come back and fix it at no charge. Call (844) 797-2573 for a free estimate.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.