Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Keypad & Intercom Repair: The Mesquite Owner’s Guide
We repair and replace Elite keypads and intercom units in Mesquite, and a typical installed repair runs $185 to $420 depending on whether we’re swapping a keypad, an intercom station, or the low-voltage wiring behind them. Most jobs are handled on a single visit. When a keypad or intercom fails, owners usually find out the same way: the gate won’t open from the driveway pad, or the house station goes silent while the gate still opens from the car remote. Sometimes it’s a dead backlight. Sometimes one digit on the keypad stops registering while the rest work fine. That last one points to a worn membrane pad, not a board failure.

Ironworks Gate Co. Mesquite is an independent service provider. We’re not affiliated with Elite, and we don’t sell Elite-branded product as an authorized dealer. What we do is diagnose, match, and install the correct part so the entry station works the way it did the day it was put in.
Key Takeaways
- Installed keypad and intercom repair in Mesquite typically runs $185 to $420.
- Most Elite entry-station failures trace to the keypad membrane, the wiring connections, or the power supply, not the whole unit.
- We quote the price before any work starts, and it doesn’t change after.
- Every repair is covered by our written 90-Day Done Right Promise.
Which Elite Models This Applies To
Elite makes a range of slide and swing gate operators, and the entry hardware that rides with them varies by series. The keypad and intercom stations we service most often sit on the residential and light-commercial slide operators, along with the swing operators used on estate driveways. The older the operator, the more likely it’s paired with a separate keypad or intercom station rather than an integrated control board.
Identifying the right part starts with the operator, not the keypad. Pull the model label off the operator housing and write down the full series designation. From there, measure the keypad post height and the distance from the post to the control box. On intercom setups, note whether the system is a two-wire or multi-wire configuration. That single detail decides which replacement will actually talk to the operator.
The OEM-versus-aftermarket call is where most Mesquite owners get stuck. Elite-branded keypads are the safest match, but they can be slow to source on older series. Quality aftermarket equivalents exist and work reliably, and they often cost 20 to 30 percent less. What matters is matching voltage, wiring protocol, and mounting pattern. We’ll tell you honestly which route we recommend for your specific operator, and why. We also service LiftMaster, Mighty Mule, and Ghost Controls entry hardware when a Mesquite gate has been upgraded or mixed over the years.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Elite Keypad & Intercom Repair Is Failing
Here’s what a failing Elite keypad or intercom actually looks like, and what’s usually behind it:
- One or more keys stop registering. This is the most common failure we see. A worn or contaminated membrane pad loses individual contacts first, while the rest of the keypad works fine. It’s a pad or keypad replacement, not a control board.
- The backlight flickers or dies. Usually a failing power supply or a corroded connection at the post. Mesquite’s summer heat and blowing desert dust get into every seam, and low-voltage connections are the first to suffer.
- The gate opens from a remote but not the keypad. That narrows it down fast. The operator is fine; the signal path from keypad to control board is the problem. Often it’s wiring or a failed keypad output stage.
- Intercom audio is one-way, garbled, or dead. On intercom stations, this points to a speaker, microphone, or wiring fault rather than the whole unit. Two-way failures are usually the house station; gate-side failures are usually the outdoor station.
- Intermittent operation after rain or temperature swings. Mesquite sees sharp night-to-day temperature swings, and small cracks in an outdoor housing let moisture in. Intermittent entry-station behavior often traces to a housing that’s no longer weather-tight.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what Elit keypad and intercom repair runs in Mesquite, broken down honestly:
| Job | Typical Installed Range |
|---|---|
| Keypad replacement (membrane or full keypad) | $185 – $290 |
| Intercom station repair or replacement (gate-side) | $240 – $380 |
| Intercom station repair or replacement (house-side) | $220 – $360 |
| Wiring, power supply, or connection repair | $150 – $320 |
| Full keypad and intercom system swap | $340 – $420 |
That price is the total, not a teaser. Parts and labor are included, and we settle the figure with you before a single bolt is turned. What moves the number is which part is actually failing, whether the wiring needs replacement, and whether the post needs any repair work. Every repair is backed by our written 90-Day Done Right Promise.
DIY or Call Us?
There’s a short list of things a Mesquite owner can safely check. Press each keypad button and note which ones fail. Look at the outdoor housing for cracks, loose screws, or dirt packed into the seams. Check that the power indicator on the operator is lit. Confirm the gate still opens from the remote. All of that is safe, and it helps us diagnose over the phone.
What we’d caution against is opening the low-voltage wiring at the post or the control box, or trying to swap a keypad without knowing the operator’s wiring protocol. Getting the wire order wrong on an Elite entry station can trip a fault on the control board and turn a $200 keypad job into a control board repair. It’s low voltage, not line voltage, but it’s still a call we’d rather make for you.
Have your keypad buttons checked and the wiring confirmed before anything is swapped. Call us at (844) 797-2573, and we’ll quote the job before we start.
We also offer a $50 discount on any repair over $250, and we’ll give a free second opinion on any written estimate you’ve already received. If you’re a senior or a veteran, your 5% discount applies, always.
FAQs
Ten to fifteen years is a fair expectation for a keypad on a well-maintained gate. Mesquite’s heat and dust tend to pull that toward the lower end. Membrane pads and outdoor housings fail before the electronics do, which is why we inspect the housing on every keypad call.
Yes, often. A single dead key or a one-way intercom is usually a component-level repair. We’ll always tell you if repair is the right call versus replacement, and price both options. Call (844) 797-2573 for an exact quote; estimates are free.
A keypad replacement is typically an hour to ninety minutes. An intercom station swap runs closer to two hours if the wiring is sound. If the wiring needs replacement, plan for a longer visit, and we’ll let you know the estimate before we start.
We match the part to your operator’s model designation and wiring protocol, not to what looks similar on the outside. Our technicians have up to 13 years of experience across the major gate-automation brands, Elite included, and we’re trained to make the right call the first time.
Call us at (844) 797-2573 for a free estimate. We answer the phone 24 hours a day, 7 days a week, with a live person on the other end.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.