Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Gate Repair in Mesquite: What to Know First
We provide independent Elite gate repair in Mesquite, and most call-outs we handle are diagnosed the same day and put right on the first visit. A worn or seized gate on an Elite arm is usually a hardware and adjustment problem, not a dead motor, and that matters for what you pay. Expect honest ranges: hinge, weld, and realignment work typically lands in the low hundreds, while operator faults run higher because the motor, arm, and control board are three separate parts. We quote before we start, and the price we agree is the price on the bill.

This page is for the homeowner with an Elite swing or slide operator already on the driveway, or an Elite arm that has stopped opening the gate the way it used to. Call us at (844) 797-2573 and a live person answers, day or night.
How Elite Products Fail – and How We Fix Them
- The operator arms and the gate sag apart. An Elite swing arm is a strong unit, so when an Elite gate starts dragging or the arm strains against the leaf, the cause is almost always a dropped hinge or a post that has shifted, not the motor. The arm forces the gate anyway until the bracket cracks or the worm gear wears. We fix the hinge and post line first, then re-check the arm under load. Treating the arm as the fault just buys you a second failure.
- The control board is blamed for a limit problem. On an Elite slide or swing setup, a gate that stops short, reverses, or won’t close fully is often a limit switch out of adjustment or debris in the travel path, not a failed board. Boards get swapped for this all the time. We test limits and travel before we price any electronics, so you don’t pay for a board you didn’t need.
- Keypad and remote failures that aren’t the keypad. If a code takes once and then quits, the usual cause is the receiver board or low voltage at the control box, not the accessory. We test the whole access chain from keypad through wiring to the board, so the part we replace is the one that failed.
- Rust and weld fatigue at the hinge points. Mesquite’s dry heat saves a lot of frames, but our summer swings from 110-degree afternoons to cool desert nights work the metal, and a hinge weld that has been flexing for years can crack quietly before it lets go. We inspect the welds, re-weld where it’s warranted, and spot-treat bare steel before it spreads.
- Locks and latches that no longer meet. A gate that has drifted off its post will throw the lock out of line, so the latch drags or won’t seat. The lock is usually fine. We realign the gate to the post and set the latch to it, rather than selling you a new lock set every season.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Elite Gate Repair Process
- 1
We answer when you call. A live person picks up at (844) 797-2573, 24 hours a day, 7 days a week. No queue, no waiting until Monday.
- 2
We come out and diagnose. A background-checked, uniformed technician checks the gate, the hinges and posts, the arm, the limits, and the control. Our technicians have up to 13 years of experience, and they’ve worked Elite alongside the eight other automation brands we service.
- 3
We quote before we touch a bolt. You get the price for the work we recommend, settled and agreed before any repair starts.
- 4
We decide parts honestly. Where an OEM Elite part is the right call, we use it. Where a quality aftermarket part does the same job for less, we’ll tell you, so you’re not paying for a label.
- 5
We do the repair and test it under real load. Open, close, limits, safety reversing, and the keypad all get cycled before we call it done.
- 6
We back it in writing. Every Elite job carries our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
What Elite Gate Repair Costs in Mesquite
These are the ranges we see on Elite jobs in Mesquite. The final price is quoted and agreed before we begin.
| Job | Typical range |
|---|---|
| Hinge and post repair, re-weld | $180-$340 |
| Gate realignment (leaf back to post, latch reset) | $150-$320 |
| Lock repair or replacement | $120-$260 |
| Weld and rust repair | $200-$450 |
| Automatic swing or slide arm repair | $250-$600 |
| Control board or limit switch fault | $280-$650 |
What moves the price: gate weight and leaf length, whether the post has shifted enough to need resetting, whether the part is OEM or quality aftermarket, and how much of the arm or control has to come apart to reach the fault. Vehicle gate access, trailer-mounted posts, and rust that has spread past the hinge all add time. The estimate is free, and you’ll never see a number on the bill that we didn’t agree with you first.
See the difference
Before
After
Before
After
Before
AfterWhy Mesquite Homeowners Call Ironworks Gate Co. Mesquite for Elite Work
We’ve been doing this work since 1984, over 42 years, and Mesquite homeowners tend to call us once and then keep our number. A live person answers the phone every hour of every day, and we will be there when we say. Every job is protected by the 90-Day Done Right Promise, written and no-hassle: if it isn’t right, we come back and fix it, no arguing. The technicians are background-checked and uniformed, and they work in your yard the way they’d work in their own mother’s.
As an independent Elite service provider, we’re trained and equipped across nine gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. That backup matters: when the right answer is on a different brand’s hardware, or you’re weighing a repair against a fresh operator, we can tell you straight because we work all of them.
FAQs
An independent repair doesn’t void an Elite warranty by itself, but how we handle the parts does. We use OEM Elite parts where the warranty is active and tell you when an aftermarket part would carry its own coverage instead, so you can choose. Call (844) 797-2573 and we’ll walk through what your situation needs.
Yes. We source Elite parts through our supply channels, and where a part is on backorder we’ll tell you the real lead time up front instead of guessing. Most repairs we handle use parts we can get without a long wait. Call (844) 797-2573 for your model and we’ll confirm availability.
Repair is the right answer most of the time, especially when the fault is in the arm, hinges, or limits rather than the motor. Replace when a control board, arm, and motor are all near the end together, or the gate hardware has failed past the point of a sound repair. We’ll price both honestly so the choice is yours.
We aim for same-day on repair calls, and a live person answers 24 hours a day, so you can call at any hour and get real help. Call (844) 797-2573 and we’ll get you on the schedule.
Yes. We quote and agree the price before a single bolt is turned, so there are no surprises on the bill. Call (844) 797-2573 for a free estimate.
Get Your Elite Gate Fixed
If your Elite gate is dragging, reversing, or refusing to close, call us at (844) 797-2573 for a free estimate. A live person answers around the clock, we’ll give you a square deal up front, and every repair is backed by our 90-Day Done Right Promise. We’d rather fix it once and have you not think about it again.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.