Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Welding & Fabrication: The Mesquite Owner’s Guide
We repair and replace failed Elite gate welding and fabrications in Mesquite, and most jobs run between $220 and $850 installed depending on whether the work is a hinge-post re-weld or a full frame section. Emergency weld repairs are often same-day. The hard part is finding a fabricator who knows the Elite gate frame geometry and won’t just tack a bead over a stress crack that needs full penetration. Call (844) 797-2573 for a free estimate.

Most Mesquite owners don’t notice the weld failed until the gate hangs crooked or drags on the driveway. Then they see the crack – usually at the hinge plate, the bottom rail, or where the pickets meet the frame. By that point the weld has been moving for months.
Key Takeaways
- Elite gate fabrications fail at hinge-plate welds and bottom-rail joints first, not randomly.
- Installed cost in Mesquite runs $220-$850 depending on scope and finish.
- We’re an independent service provider working on Elite gates – not affiliated with Elite.
- Every job is covered by our written 90-Day Done Right Promise.
Which Elite Models This Applies To
Elite builds a wide spread of residential swing and slide gates, and the fabrication – the welded steel or aluminum frame your motor moves – varies by series. The weld spec that matters most is the hinge-post connection: Elite uses a heavier gauge tube on its estate frames than on its lighter walk-through models, and welding a light-gauge patch onto a heavy-gauge post guaranteed a re-crack within a season. We match the filler and heat range to the base metal, not to what’s convenient.
How to identify what you have: the frame label is usually welded to the inside of the bottom rail or stamped on the hinge stile. If it’s unreadable from weathering – common on Mesquite gates after ten summers – we take frame dimensions and hinge spacing instead, and we can proceed from those. You do not need to find the exact model number for us to weld it right.
OEM vs aftermarket: on a gate frame there’s rarely an “OEM weld” to buy. What matters is matching the steel grade, thickness and finish to the original. When a gate-specific part is required – an Elite hinge, a manufactured bracket, a capture plate – we source the correct spec and tell you plainly whether it’s a factory part or a quality equivalent. We don’t carry parts on a truck, and we don’t claim to have a warehouse full of Elite spares. We measure, order precisely, and return with the right piece.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Elite Welding & Fabrication Is Failing
Cracks don’t announce themselves. These are the five we see most on Elite gates across Mesquite:
- Gate sags or droops at the latch side. The hinge-plate weld has started to fail and the gate has lost its square. You’ll see the gap open up before the weld is visibly cracked.
- Visible hairline crack in the finish near a hinge or corner. The paint has cracked because the steel under it has flexed. That flexibility is the weld failing, not a cosmetic flaw.
- Rust bleeding at a joint. Water gets in through a stress crack and the weld seam can look intact while the metal behind it is already compromised. Common on bottom rails that sit low to the ground.
- Popping or grinding sound as the gate moves. The operator is pushing against a frame that’s shifting. If the gate shakes, the fabrication is moving and the motor is carrying load it shouldn’t.
- Gate drags on the driveway. A weld failure at the hinge side drops the whole frame. This puts the operator and the hinges under strain and shortens motor life if left alone.
Elite gates are vulnerable in Mesquite’s summer heat and long dry spells because the temperature cycling works the weld joints – steel and aluminum expand and contract differently, and a weld that was marginal when new will fail after enough seasons. Wind load from the open desert blow adds another stress cycle. Call (844) 797-2573 for a free estimate.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest range for welding and fabrication on an Elite gate in Mesquite:
- Spot weld repair (single hinge or picket): $220-$380 installed, includes prep, weld, and rust-inhibiting finish.
- Hinge-post re-weld or hinge-plate replacement: $350-$550 installed, includes geometry check and re-hanging.
- Full frame section rebuild (bottom rail, corner, or stile): $550-$850 installed, includes stock match and full re-square.
- Finish work (paint or powder-coat touch-up): included as standard on all repairs, not added later.
What drives the range: base metal (aluminum runs higher than steel), accessibility (a post tight against a wall or landscaping slows the work), and whether the gate has to come off to be repaired properly. What’s included: prep, correct filler, the weld itself, finish, and a full open-and-close cycle test against your Elite operator before we leave. The price is quoted and agreed before any work starts. No invoice surprises.
Every weld job carries our 90-Day Done Right Promise – a written guarantee with no paperwork and no arguing. And our current standing offers apply: $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% senior and veteran discount. Our technicians have up to 13 years of experience.
DIY or Call Us?
Here is where a homeowner should draw the line. You can safely check for cracks, look for rust bleeding at joints, check hinge bolts for looseness, and test whether the gate swings square with the operator off. Those checks tell you what’s failing. What you can’t do safely at home is weld a structural joint on a gate that could come down on you or fall onto a vehicle in the driveway. Structural welding is the part that needs a trained fabricator, proper heat and filler selection, and a finish that stops rust in Mesquite’s dry climate.
The other reason to call is the operator. If the gate has been moving because the weld failed, the motor has been carrying that strain – and that becomes a separate problem if it’s left. We check both the weld and the automation during a repair visit. Our technicians have up to 13 years of experience and we can often fix a failing weld and reseason the hinges on the same trip.
Call (844) 797-2573 for a free estimate. A live person answers the phone 24 hours a day, 7 days a week.
FAQs
A properly welded joint on an Elite gate frame should last 10 to 15 years before the heat cycling in a Mesquite summer starts to work it again. A patch weld that only sits on the surface will crack again within a season or two. We prep, weld to full penetration where the joint requires it, and apply a finish that keeps water out of the seam.
Yes, most weld failures can be repaired without replacing the gate. Spot cracks and hinge-plate failures are the most common repairs. Full frame section rebuilds are sometimes the only option at a badly rotted bottom rail, but we tell you that before work begins, not after. Call (844) 797-2573 for a free estimate.
A spot weld or hinge-plate repair is typically done in a single visit of two to four hours, including set-up, weld, finish and a full open-and-close test against your Elite operator. A full frame section rebuild takes longer and may require a return visit to allow the finish to cure. We don’t promise same-day on scheduled fabrication work; we measure, order the correct part and return ready to weld.
We source the correct spec for the part, not a generic substitute. For steel and aluminum weld repairs there’s rarely an “OEM weld” to buy – what matters is matching steel grade, thickness and finish to the original. When a gate-specific manufactured part is required, we order it precisely and return with the right piece. We’re an independent service provider and not affiliated with Elite. Call (844) 797-2573 – estimates are free.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.