Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Keypad & Intercom Repair: The Mesquite Owner’s Guide
We install Linear-compatible keypads and intercoms in Mesquite, and most replacements run $285 to $520 installed depending on the model and whether we’re swapping the keypad alone or wiring a new intercom station. On repair calls, we can often get out same day; call us at (844) 797-2573 and a live person will pick up, day or night.

Most owners discover the failure the same way. The keypad beeps but the gate won’t open. Or the front intercom crackles when a visitor presses the button, or it just goes silent and the gate becomes a mystery to anyone who doesn’t have a remote. In Mesquite, that’s a real problem by June – a visitor standing in 108-degree heat at a dead keypad doesn’t wait long before they give up and drive off.
A quick note on who we are: Ironworks Gate Co. Mesquite is an independent service company, not affiliated with Linear. We service Linear equipment alongside eight other major brands, including LiftMaster, Mighty Mule, and Ghost Controls, and every completed replacement is covered by our written 90-Day Done Right Promise.
Which Linear Models This Applies To
The Linear product line is broad and the parts don’t always cross over cleanly. The two most common families we see on Mesquite driveways are the AK-11 style post-mount keypads (often paired with Linear gate operators like the AK-11‘s companion access controllers) and the AM/AM3 intercom stations that ship with Linear’s telephone-entry systems. If you’re trying to identify your part, look for a model sticker on the back plate or inside the housing – it’s usually a small white label with a part number starting with “AK,” “AM,” or “RE.” Measure the mounting footprint if the label is gone; Linear has used at least three different bolt patterns across its post-mount keypads, and getting that wrong means drilling new holes in your pillar.
When it’s time to replace, you have a choice. OEM Linear parts match the original exactly and keep your existing wiring and mounting intact. Quality aftermarket equivalents can shave $40 to $80 off the part cost and are often just as dependable for a homeowner whose keypad isn’t tied into a larger access-control network – but you need to confirm compatibility with your operator before ordering, because some aftermarket keypads don’t speak the same signal protocol as an older Linear receiver. We see that mismatch fail most often on gates originally installed in the late 1990s and early 2000s. The honest answer we give Mesquite owners: if the gate is working well otherwise, matching OEM is usually the cleanest path. If you’re not sure which you have, we’ll identify it on the visit – no charge to look.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Linear Keypad & Intercom Repair Is Failing
Linear keypads and intercoms tend to fail in recognizable ways. Here’s what each symptom usually tells us:
- Keypad beeps but the gate doesn’t move. The keypad is sending a signal, but the receiver in the operator isn’t picking it up – usually a failing receiver board or a bad signal wire connection at the operator box. Common after a Mesquite monsoon season has worked on the low-voltage wire.
- Keypad completely dead, no lights, no beep. Power isn’t reaching the unit. Could be a blown fuse at the transformer, a corroded wire nut, or the keypad board itself has failed. We check the transformer first because it’s the easiest fix.
- Some buttons work, others don’t. The membrane has worn through on the high-traffic digits. On a Linear keypad that’s often 7-10 years of use in our climate – the plastic gets brittle faster in the dry heat, and a worn membrane traps grit that accelerates the failure.
- Intercom crackles or is one-way only. The speaker or microphone element has aged out, or moisture has gotten into the housing. In Mesquite, the dust is as much a culprit as rain – it packs into the speaker grille and muffles the audio over time.
- Code accepts but the gate opens on the wrong code or randomly. This is the tricky one. On an older Linear keypad it can mean the memory chip is confused, but it can also mean someone nearby is running a compatible transmitter, or the receiver’s code memory has corrupted. Worth a diagnostic before replacing a part that isn’t the problem.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here are the installed price ranges we quote in Mesquite. These are parts-plus-labor, and the price is settled before we turn a bolt – you’ll know the number before we start.
- Post-mount keypad replacement (Linear-compatible, standard model): $285-$380 installed
- Telephone-entry keypad (Linear AM-series compatible): $340-$450 installed
- Intercom station replacement (single-station): $390-$520 installed
- Existing keypad receiver board swap (keypad stays, board replaces): $240-$320 installed
- Wiring repair only, no part replacement: $145-$210
What drives the range up: model specificity (some Linear parts are harder to source than others), whether the mounting footprint has to be reworked, and whether the low-voltage wiring needs to be re-run. We’ll tell you which one you’re in before we quote. If the diagnosis points to something we can repair rather than replace – a bad wire nut, a corroded terminal – we’ll do that instead of selling you a new part. Our $50 Off Any Repair Over $250 offer applies here, and we also offer a Free Second Opinion on any written estimate if you’ve already been quoted elsewhere. Every replacement is backed by the 90-Day Done Right Promise: if it’s not right, we come back and make it right, no arguing.

DIY or Call Us?
Some of this you can check safely. Others, honestly, is where we see homeowners get into trouble.
Safe to check yourself: whether the keypad has power (look for the LED), whether the gate works fine from a remote (that tells you the operator and receiver are healthy and the problem is at the keypad), and whether the mounting screws are tight. A visual check of the keypad wiring for obvious corrosion or a loose wire is also fair game if the unit is easily accessible.
Where DIY goes wrong: pulling the keypad housing to swap the board, re-running low-voltage wire through a pillar, and troubleshooting a receiver that’s misbehaving. The low-voltage side isn’t lethal, but a homeowner who crosses the wires at the transformer can blow a fuse in the operator – turning a keypad fix into a gate-down service call. And if the gate operator itself is involved in the diagnosis, that’s the point to stop. Linear gate operators run on 120V and have capacitors that hold a charge. We don’t recommend homeowners open the operator housing.
If the keypad is dead and you’re not sure why, call us at (844) 797-2573. A live person answers 24/7, and repair calls can often be worked in same day.
FAQs
Plan on 8-12 years for a Linear keypad in the Mesquite climate and 7-10 years for an intercom station. The dry heat and dust shorten the membrane life compared to coastal climates, and units in full sun on an unshaded gate pillar tend to go first. If you’re past the 10-year mark and seeing multiple small problems, replacement is usually the better call than chasing repairs.
Sometimes, yes. A dead keypad caused by a bad transformer, a corroded wire nut, or a loose terminal is a repair – usually $145 to $210. A membrane that’s worn through on certain digits, or an intercom speaker that’s failed, is a replacement because those parts aren’t field-repairable on most Linear units. We diagnose first and quote the repair and the replacement side by side so you can choose. Call (844) 797-2573 for a free estimate.
A post-mount keypad swap is typically 45 minutes to 1.5 hours on site, assuming the wiring is sound and the mounting footprint matches. An intercom station replacement can run 1.5 to 2.5 hours if the wiring needs re-terminating. The receiver board swap is often the quickest job – usually under an hour. We’ll give you the time estimate with the price quote so you can plan your day.
We order the correct Linear-compatible part for your specific model and confirm it against your operator before the visit. If it’s an OEM part that takes a few days to arrive, we tell you upfront – we don’t want you waiting in the driveway wondering why the gate isn’t done. For most Linear keypads and intercoms, we can source within a few business days. The part is quoted as part of the upfront price, so there’s no surprise markup on the invoice.
If you’ve got a Linear keypad that’s gone quiet or an intercom that’s crackling, call Ironworks Gate Co. Mesquite at (844) 797-2573 for a free estimate. We’ll identify your model, tell you honestly whether it’s a repair or a replacement, and settle the price before we start. Our technicians bring up to 13 years of experience to every job, and every completed job is backed by the 90-Day Done Right Promise. A live person answers the phone, 24 hours a day, 7 days a week.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.