Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Motor & Opener in Mesquite: What to Know First
We provide independent Linear gate motor and opener service in Mesquite, and most Linear repair jobs are finished in a single visit with the price settled before we start. We’re an independent Linear service provider, not affiliated with or authorized by the manufacturer, so our only loyalty is to getting your gate working correctly. Expect an honest, written price and a 90-Day Done Right Promise behind the work.

This page is for Mesquite homeowners with a Linear operator on the driveway – an older swing or slide gate that opened fine for years and has started to hesitate, reverse, or quit entirely. If that’s you, call (844) 797-2573 and a live person will answer, day or night.
How Linear Products Fail – and How We Fix Them
Linear makes solid residential operators, but the failures we see in Mesquite homes are specific to the brand and to the desert. Here’s what actually goes wrong and what we do about it.
- Control-board corrosion on the LDO and LA400 swing operators. Mesquite’s summer heat and the occasional monsoon blowing grit and moisture into an exposed control box cause the limit and reverse-logic circuits to act up. You’ll see the gate reverse mid-travel or stop short. We test the board against the arm travel, and when the board is the culprit we replace it with the correct OEM board rather than a generic one that won’t hold calibration.
- Gear and drive-train wear on the LA400. After years of daily cycling, the arm’s internal gears and the operator’s drive components wear unevenly. The symptom is a grinding or growling sound before the gate even moves. We open the unit, check the gear set and motor brushes, and tell you plainly whether a gear kit restores it or the unit is past saving.
- False obstructions from the safety edges and photo eyes. Linear boards are tuned to expect a clean signal from the reversing devices. In Mesquite, dust films on the photo-eye lenses and aged safety-edge wiring cause the operator to read a phantom obstruction and refuse to close. We clean and re-aim the eyes and test the edge circuit end to end.
- Battery-backup and low-voltage failures. Linear’s battery-backup units live in the same box as the control board, and Mesquite’s heat cooks batteries faster than you’d expect. When the gate won’t run during a power blip, the battery, the charging circuit, or both need checking. We test under load, not just at the terminals.
- Radio and intercom pairing drift. Older Linear receivers can fall out of sync with remotes and intercom call buttons after a component ages. We re-pair the radio and integrate the intercom cleanly so one button reliably opens the gate, instead of the two. This is where we tell owners most often that a fresh remote is not the fix.
On every one of these, we make the OEM-versus-aftermarket call honestly: genuine Linear parts where the control logic depends on them, quality aftermarket where it doesn’t, and we never void your operator’s coverage to save a dollar on a part.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Linear Gate Motor & Opener Process
- 1
Call and live answer. A real person picks up, 24 hours a day, seven days a week. We ask what your Linear gate is doing and set a visit that fits your day.
- 2
On-site diagnosis. Our background-checked, uniformed technician – with up to 13 years of experience on gate automation – checks the operator, the board, the safety devices, and the gate’s mechanical travel before touching a part.
- 3
The parts decision. We tell you what failed, whether an OEM Linear part or a quality aftermarket equivalent is the right call, and why. Fixed price agreed before any work begins.
- 4
The repair. Control board, gear set, battery, radio, safety edge, or intercom integration – whatever the honest fix is, done correctly the first time.
- 5
The full test. We cycle the gate, check reverse logic and the safety edges, and confirm the Linear operator runs and stops exactly as it should.
- 6
The guarantee and cleanup. You get the written 90-Day Done Right Promise, and we leave your driveway the way we found it.
See the difference
Before
After
Before
After
Before
AfterWhat Linear Gate Motor & Opener Costs in Mesquite
Here’s what Mesquite homeowners actually pay for common Linear work. Every price is quoted and agreed before a single bolt is turned.
| Linear job | Typical range |
|---|---|
| Diagnostic visit and adjustment | $89 – $150 |
| Control-board replacement (LDO, LA400) | $280 – $520 |
| Gear kit / drive-train repair | $300 – $600 |
| Battery-backup replacement (parts + labor) | $180 – $340 |
| Safety-edge or photo-eye repair | $150 – $325 |
| Remote re-pair and intercom integration | $120 – $260 |
What moves the price: which Linear model line you have, whether the board or the gear set is the true failure, and whether an intercom is part of the fix. Call (844) 797-2573 for a free estimate on your Linear job and (if you have another quote) a free second opinion on it.
Why Mesquite Homeowners Call Ironworks Gate Co. Mesquite for Linear Work
Most Linear repairs are a single visit, and the price doesn’t move after we start. A live person answers every call, 24 hours a day, seven days a week – no voicemail tree, no waiting until Monday. Our technicians know Linear operators specifically, and when a job calls for it we’re trained on the other major brands too, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing.

Every Linear job is covered by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right, no arguing. And right now we’re running $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
FAQs
Do you work on Linear operators you’re not an authorized dealer for? Yes. We’re an independent Linear service provider, which means we service your operator and make the honest fix without any manufacturer tie. That freedom lets us recommend the right part for your gate rather than the one a brand tells us to push.
Can you get genuine Linear parts for my older model? Usually. Many Linear model lines still have OEM boards and gear kits available, and where they don’t we use a quality aftermarket equivalent that holds calibration. We’ll tell you up front which path your job needs and what it costs.
How fast can you fix my Linear gate in Mesquite? Most Linear repairs are finished in a single visit, and we take calls 24 hours a day. Call (844) 797-2573 and a live person will get you on the schedule – estimates are free.
Should I repair my Linear operator or replace it? It depends on what failed. A board or battery is almost always worth repairing. A worn gear set on an old unit is a judgment call, and we’ll show you the numbers both ways. We never push a replacement you don’t need.
Will the work be covered if something goes wrong? Yes. Every Linear job carries our written 90-Day Done Right Promise – if it isn’t right, we come back and make it right. Call (844) 797-2573 for a free estimate on your Linear gate motor or opener.
Ready to get your Linear gate working the way it should? Call Ironworks Gate Co. Mesquite at (844) 797-2573 for a free estimate. A live person answers every call, the price is agreed before we start, and every job is done right – and backed in writing.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.