Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Repair in Mesquite: What to Know First
We provide independent Linear gate repair in Mesquite, and most Linear jobs are diagnosed and fixed on a single visit. Common repairs land between $180 and $420 depending on whether the problem is mechanical (hinges, welds, alignment) or electronic (control board, receiver, safety edges). We’re an independent Linear service provider, not affiliated with or authorized by Linear, and we quote every job in writing before a bolt is turned.

This page is for the homeowner with a Linear operator already on the gate post, or one going in soon, who wants the fix done correctly the first time. Our technicians have up to 13 years of experience, and we service nine gate-automation brands so the right part goes on regardless of what’s on the driveway. Call (844) 797-2573 and a live person answers, day or night.
How Linear Products Fail – and How We Fix Them
Linear makes reliable residential swing and slide operators, and the failures we see in Mesquite are predictable once you know the line. Here’s what actually breaks and what we do about it.
- Control board failure on Linear swing operators (LSO and similar residential swing lines). The symptom is usually a gate that runs partway and stops, or one that reverses mid-travel with no obstruction present. Heat is the usual culprit; a control board sitting in a metal housing through a 110°F Mesquite July cooks the capacitors over time. We test the board under load, confirm it’s the board and not the motor or limits, then replace with an OEM board so the operator’s programming and safety logic stay intact.
- Receiver and remote pairing drift. Remotes that work one day and quit the next, or that only work within ten feet, usually point to a failing receiver module or antenna connection, not the remotes themselves. Homeowners often buy new remotes first. We check the receiver and antenna lead before selling anyone a remote they don’t need.
- Limit switch and cam wear on slide operators. When a Linear slide gate stops short of fully closing or slams the last few inches, the travel limits have drifted. On a strong wind day, the gate can hit the stop and stall the motor. We reset the limits, inspect the cams for wear, and check the track for debris and heat warp. This is one of the cheaper fixes we do, and it’s frequently misdiagnosed as a dead motor.
- Safety edge and photo-eye faults. A gate that reverses on closing with nothing in its path is usually telling you a safety edge has failed or a photo-eye is misaligned. In Mesquite, dust and fine sand collect on the lenses and the edge’s rubber channel hardens in the sun. We test the edge resistance and the eye alignment with a meter, replace the failed component, and re-verify the reverse cycle.
- Arm, bracket and hinge fatigue. Linear swing arms and the brackets that hold them take the load of every open and close. Over years, the mounting bracket loosens from the post and the arm develops play, which throws off the gate’s alignment and strains the operator. We weld or re-secure the bracket, realign the gate, and check the hinges, since a sagging hinge will keep working a good operator to death.
One parts nuance worth knowing: Linear’s own site won’t tell you that aftermarket control boards for some residential swing lines have a different terminal layout than the OEM board, which means a “compatible” replacement can work but leave your existing accessories wired differently. We use OEM boards on Linear operators whenever they’re available, and when they aren’t, we tell you what changes before we install anything.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Linear Gate Repair Process
- 1
The call. A live person answers, 24 hours a day, every day. We ask what the gate is doing, get the operator model if you have it, and book a window. You’ll know the price range before we arrive.
- 2
Diagnostics on site. We test the operator under load, check power at the board, verify the limits and safety devices, and inspect the gate’s mechanicals (hinges, posts, arm, track). Most Linear problems get isolated in the first twenty minutes.
- 3
The parts decision. We tell you whether the fix calls for an OEM Linear part or a quality aftermarket equivalent, what each costs, and what difference it makes. You approve before we proceed, and the written price is settled first.
- 4
The repair. We make the fix, whether that’s a board swap, a limit reset, a safety-edge replacement, or welding and realigning the gate itself.
- 5
The test. We run the gate through a full open-and-close cycle, test the safety reverse and the photo-eyes, and confirm the limits hold. We don’t leave until it does what it should, every cycle.
- 6
The guarantee and cleanup. We clean up the site, hand you the written 90-Day Done Right Promise, and leave our number. If anything isn’t right in 90 days, we come back and make it right, no arguing.
See the difference
Before
After
Before
After
Before
AfterWhat Linear Gate Repair Costs in Mesquite
Here’s what Linear work actually runs in the Mesquite market. These are real ranges, and we confirm your number in a free written estimate before any work starts.
| Linear repair | Typical price |
|---|---|
| Diagnostic visit (credited toward the repair) | $79 – $125 |
| Limit switch / cam reset and realignment | $140 – $220 |
| Receiver or remote re-pairing, antenna repair | $120 – $200 |
| Safety edge or photo-eye replacement | $180 – $320 |
| Control board replacement (OEM) | $280 – $480 |
| Hinge, bracket or weld repair | $160 – $350 |
What moves the price: OEM versus aftermarket parts, whether the gate itself needs realignment or welding, and how accessible the operator is. A gate on a level driveway with a straightforward board swap sits at the low end. A sagging gate that’s been straining the motor for a year costs more because the mechanical fix has to happen alongside the electronic one.
We quote the price and agree on it before a single bolt is turned, so there are no surprises on the bill. Call (844) 797-2573 for a free estimate.
Why Mesquite Homeowners Call Ironworks Gate Co. Mesquite for Linear Work
Our technicians have up to 13 years of experience, and we’re trained on nine gate-automation brands, so when your Linear operator needs a fix, we’re not learning on your gate. We carry the parts or get them fast, which is why most Linear jobs finish in one visit. If a control board is discontinued or back-ordered, we tell you straight and lay out the options rather than leaving your gate stuck open.
Every job comes with our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. A live person answers the phone 24 hours a day, so a gate that fails on a Sunday night doesn’t wait until Monday. And because we also service LiftMaster, Mighty Mule, Ghost Controls and DoorKing, we’re the call whether you own a Linear or a mix of systems. Standing offers include $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
FAQs
No, as long as the work uses OEM or approved parts and doesn’t alter the operator’s safety systems, an independent repair won’t void a Linear warranty. We use OEM boards and components on Linear units whenever they’re available, and we tell you upfront if a fix would affect coverage. Call (844) 797-2573 for a free estimate.
Usually yes, though some discontinued Linear boards are getting harder to source. When an OEM part is back-ordered, we lay out the aftermarket option and what changes, so you decide with the facts. Most parts arrive within a few days. Call (844) 797-2573 and we’ll check availability for your model.
Repair if the operator is under about ten years old and the failure is a board, limit, receiver or safety device, since those fixes are cheaper than a new unit. Replace when the motor itself is failing or parts are discontinued and the cost approaches a new install. We’ll give you both numbers honestly and let you choose. Call (844) 797-2573 for a free estimate.
Most Linear gate repairs are completed on a single visit, often the same day you call for common failures like limit resets and receiver faults. Control board replacements depend on part availability, and we’ll tell you the timeline when we quote. A live person answers 24 hours a day. Call (844) 797-2573.
We service both Linear swing and slide operators, including the limit, track and safety-edge work slide gates need. The failure modes differ, so we test the operator and the gate’s mechanicals together. Call (844) 797-2573 for a free estimate.
If your Linear gate is sticking, reversing, or won’t respond, call Ironworks Gate Co. Mesquite at (844) 797-2573 for a free estimate. A live person answers 24 hours a day, we quote the job in writing before any work starts, and every repair is backed by our written 90-Day Done Right Promise. Done right, and backed in writing.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.