LiftMaster operators
Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gatesFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLiftMaster Keypad & Intercom Repair: The Mesquite Owner’s Guide
LiftMaster keypad and intercom repair in Mesquite typically runs $175 to $420 installed, depending on whether we’re replacing a wired keypad, a wireless one, or an intercom station, and most jobs are finished in a single visit. We service LiftMaster equipment across Mesquite, from Sun City to newer builds off Pioneer Boulevard, and a live person answers the phone any hour of the day or night to get you on the schedule.

Owners usually find out the keypad has failed the same way. The gate opens fine from the car remote, but the code that worked for years suddenly does nothing. Sometimes the keypad lights stay dark. Sometimes the intercom crackles, or the call button rings inside the house but no voice comes through. The gate itself is healthy; the entry point is what quit. Ironworks Gate Co. is an independent service provider and is not affiliated with LiftMaster.
Which LiftMaster Models This Applies To
LiftMaster gate operators use a handful of accessory lines, and matching the right keypad or intercom to the operator matters more than most homeowners expect. The common wired keypads are the KPW250 and its older siblings, which run on low-voltage wiring back to the operator. Wireless keypads like the 878MAX and 877MAX are stand-alone and pair to the receiver in the control box. On the intercom side, LiftMaster’s gate intercom stations tie into the operator’s accessory terminals, and the match depends on whether your operator has a dedicated intercom input or needs a separate interface.
Serial numbers matter here. LiftMaster’s control boards changed accessory compatibility across model generations, so a keypad that worked on an early LA400 may not handshake with a later revision of the same model name. We ask for the model and serial off the operator label, and the age of the keypad if you know it, before we source anything. Reading the label is the single most useful thing you can do before calling.
OEM versus aftermarket is a real decision on LiftMaster. Genuine LiftMaster keypads cost more, but the pairing and the warranty are straightforward. Quality aftermarket equivalents can save money, though wireless keypads that don’t match the operator’s frequency and rolling-code protocol will pair once and then drop off. We’ve seen cheap aftermarket wireless keypads fail to hold a code through Mesquite’s summer heat within a single season. We source the part that fits your operator, not the cheapest box on the shelf.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your LiftMaster Keypad & Intercom Repair Is Failing
Here’s what failing keypads and intercoms actually look like on the ground in Mesquite:
- Code accepted, gate won’t move. The keypad is fine but the wiring or the operator’s accessory terminal has an open circuit, so the signal never reaches the control board.
- Keypad lights dark or flickering. Power at the keypad has dropped, either from a failed transformer, a corroded low-voltage splice, or a keypad that took on water.
- One digit goes dead. A single worn membrane key or a cracked button pad. That’s a keypad replacement, not a programming issue.
- Intercom rings inside but no voice. The speaker or microphone has failed, or the wiring between the station and the house unit has corroded at a splice.
- Intermittent operation on hot afternoons. Heat is a real factor here. Mesquite summers push pavement and keypad housings well past what the component was rated for, and aging keypads start dropping codes as the day heats up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what keypad and intercom work actually runs in Mesquite, parts and labor together:

| Work | Typical Installed Range |
|---|---|
| Wired keypad replacement (programmed to your code) | $175 – $280 |
| Wireless keypad replacement (paired to operator) | $195 – $320 |
| Intercom station or house unit replacement | $240 – $420 |
| Wiring repair, splice, or low-voltage power run | $120 – $260 |
What drives the range is the operator age, the condition of the wiring, and whether you want OEM or a quality equivalent. The price is settled and agreed before a bolt is turned, so there’s no surprise on the bill. Every keypad and intercom job we complete is covered by our written 90-Day Done Right Promise. We’re trained on nine brands, so if the fault turns out to sit inside the operator rather than the keypad, we don’t have to call someone else out. Our standing offers include $50 Off Any Repair Over $250 and a Free Second Opinion on any written estimate.
DIY or Call Us?
Changing a battery, re-entering your code, and checking that the keypad is getting power are all things an owner can do safely, and we’d rather you check before calling. Where DIY goes wrong is inside the operator and in the low-voltage wiring. Keypads and intercoms run low voltage, but that wiring is tied into a control board that also carries line voltage, and a homeowner who opens that enclosure without knowing where the mains enter is working next to a live circuit. The temptation to splice a fresh keypad wire into an old one to save a little is the other common mistake. It pairs once, works for a week, and fails at the splice.
When the keypad and the operator are involved, that’s the time to call. Give us a ring at (844) 797-2573 and we’ll tell you honestly whether it’s a same-day swap or a scheduled job.
Frequently Asked Questions
You’ll typically get 6 to 10 years from a quality keypad, and often less in Mesquite, where summer heat and direct sun on the housing shorten the life of the membrane buttons. Intercoms often outlast keypads since they see less finger traffic. When one starts failing, the fix is usually a straight replacement.
Sometimes, yes. A failed splice, a dead transformer, or a corroded terminal block is a repair, and we’ll fix it and be done. A keypad with worn or cracked buttons is a replacement, because there’s nothing to repair inside that housing. We’ll tell you which it is before we start.
Most keypad replacements take under an hour, and intercom work is usually an hour or two depending on wiring. If the run is in good shape, you’re back to your gate code the same visit. If the wiring needs attention, we’ll quote that before we start the work.
We match the part to your operator’s model and serial, then order OEM or a quality equivalent based on what your operator actually pairs with. No cutting corners on the frequency protocol. And if a different brand fits better, we also service Mighty Mule, Ghost Controls, and DoorKing. Call (844) 797-2573 for a free estimate. Estimates are free, and we’ll give you a straight answer about what your LiftMaster needs.
Written by the team at Ironworks Gate Co. Mesquite, serving Mesquite and nearby areas.